D-D JumpGuard Pro Aquarium Cover & Parts

Description

**The 120cm Jump Screenis classified asa bulky item. A shipping surcharge may be required for regional WA and Eastern States customers. Bulky items are not covered under Free Freight **

Jumpguard Pro DIY Aquarium Cover

There is nothing worse than coming down in the morning to finding your favourite fish lying dead and crispy on the carpet.

Many fish, especially wrasse, have a tendency to jump from the tank when frightened or chased by another fish and so a solution to preventing the loss of such fish should be high on every fish keepers priority list.

D-D Jumpguard covers are avery lightweight, sleek, low visual impact and easy to construct screen cover suitable for most aquarium types, specifically designed to prevent fish loss due to jumping whilst maintaining high light penetration.

The new Jumpguard Pro now includes cutout and brace bar parts as standard and an aesthetic black mesh.

Available sizes

Available in the following versions and are designed to be cut to size:

• TC7575PRO75cm x 75cm nominal size.
• TC12075PRO 120cm x 75cmnominal size.
• TC18090PRO 180cm x 90cmnominal size.

Notes:

1. The maximum size frame that can be made from each kit will be 3.6cm longer than stated in each direction.
2. The tank should be measured from inside face of glass to inside face of glass.

Included in the kit

TheJumpguard Pro Aquarium Coveris a kit of parts which allows the aquarist to create a custom frame for their specific aquarium.The rigid corners and extruded aluminium sectioncreate a very solid frame whichsits neatly inside glass of the aquarium glass, resting onthe top lip.

Kit Contents:

TC7575
90cm x 90cm 1PC bird mesh, black material
5 x 75cm lengths of section in black extrusion profile
1 x red spline roller tool
6 x black standard corners
Black spline,total length 3.5m
2 x Black finger pull
2 x Reverse corner
1 x 75cm brace bar
4 x brace clips

TC12075
140cm x 90cm 1PC bird mesh, black material
3 x 75cm + 2 x 120cm lengths of section in black extrusion profile
1 x red spline roller tool
6 x black standard corners
Black spline, total length 4.4m
2 x Black finger pull
2 x Reverse corner
2 x 75cm brace bar
6 x brace clips
2 x T corners

TC18090
200cm x 110cm 1PC bird mesh, black material
90cm lengths of section in black extrusion profile
1 x red spline roller tool
6 x black standard corners
Black spline, total length 5.9m
2 x Black finger pull
8 x brace clips
3 x 90cm brace bar
2 x Reverse corner
2 x T corner

Features of the Jumpguard Pro Aquarium Cover

NEW PROFILE DESIGN
The special extruded aluminium profile is now shaped with a lip which sits directly onto the edge of the glass, removing the requirement for any additional clips or brackets. The section is extruded then powder coated in a tough, low sheen, black finish for greater scratch resistance and greater aesthetics.

SPECIAL CORNERS INTEGRATE WITH SILICONE JOINTS
The lower section of the corners is specifically designed so that it does not interfere with the silicone bead in the corners of your tank which gives a tight fit to the glass with no gaps. It also makes it easier and neater to cut off the corner if you want to bring wires out at the back of the tank for pumps and heaters.

NEW BLACK MESH WITH MAXIMUM LIGHT PENETRATION
For those concerned with loss of light penetration into your reef tanks, we tested light levels with a Apogee MQ-200 meter and got the following results:
PAR without cover around 390 400 PAR with cover around 380 390 Approximately a 2.5% reduction in light with no shadowing at all.

NEW Jumpguard PRO BLACK VERSION

Mesh up close

The new Jumpguard PRO is supplied with the new black as standard in all sizeversions.

Over aquarium

On the tank it is much harder to see than the clear mesh as you do not get the same light bounce back.

Compared with clear

Here you can see the difference between the black mesh laid over the conventional clear mesh.